2000 > 2006
NOTE : Make sure the drivers door is OPEN and UNLOCKED and the key is out of the ignition.
1. INSERT and REMOVE the key from the ignition 2 TIMES, do not turn.
2. CLOSE and OPEN the drivers door twice within 40 seconds.
3. INSERT the key into the ignition and remove it again.
4. CLOSE and OPEN the drivers door twice within 40 seconds again.
5. CLOSE the door.
6. Insert the key into the ignition key cylinder.
7. Turn the ignition switch from LOCK to ON and back to LOCK at about 1 second intervals
to select the desired mode.
NOTE : 1 time for ADD.
NOTE : 2 times for REWRITE.
NOTE : 3 times for CONFIRMATION.
NOTE : 5 times for PROHIBITION.
8. Remove the key from the ignition.
9. To confirm your selection of all modes except CONFIRMATION, the power locks
will now cycle LOCK to UNLOCK the number of times corresponding to your selection.
NOTE : If CONFIRMATION mode has been selected, the power door locks will now cycle
(in 2 second intervals) the number of times corresponding to the number of transmitters currently registered.
NOTE : Opening the door will complete the procedure.
NOTE : If PROHIBITION mode has been selected, opening the door will complete the procedure.
10. For ADD or REWRITE, within 20 seconds of Door Lock confirmation follow :
(a) Press both transmitter LOCK and UNLOCK buttons simultaneously between 1 and 1.5 seconds
and release.
(b) Within 3 seconds of step (a), press the transmitter LOCK button for more than 1 second and
release.
(c) If the transmitter has been successfully programmed, the power locks will cycle LOCK to UNLOCK.
once at this time. If there are problems with the procedure used up to this point, the locks
will cycle twice, in which case you must go back and repeat the above steps (a) and (b).
(d) If multiple transmitters are to be programmed, repeat the above steps (a) to (c).
11. Open the drivers door to complete the procedure.
RS3200
DEALER
FITTED REMOTE KEYLESS ENTRY PROGRAMMING
RS3200
(TVIP)
DEALER
FITTED REMOTE KEYLESS ENTRY PROGRAMMING
NOTE : Maximum of 4 remote
transmitters can be programmed.
NOTE : When a new remote
transmitter it will be programmed in normal mode, additional options for this
system
can be setup by referring to the main operating manual of this system.
1. Open the drivers door and remove the ignition
key.
2. The programming steps must be performed within 40 seconds.
3. Insert the key into the ignition 2
times.
4. Close then open the drivers door 2 times.
5. Insert the key into the ignition 1
time.
6. Close then open the drivers door 2 times.
7. Insert the key into the ignition and leave it in.
8. Close the drivers door.
9. Turn the ignition key from LOCK
to ON, and then back to LOCK position.
10. Remove the key.
11. The tail/rear lights will flash once, the sounder will sound once and
the doors will LOCK and UNLOCK.
12. Press the LOCK and UNLOCK button once together on the
remote transmitter to be programmed.
13. Press the LOCK button on the
remote transmitter.
14. The tail/rear lights will flash once, the sounder will sound once and
the doors will LOCK and UNLOCK.
15. Repeat steps 12 to 14 for any additional remote transmitters.
16. Open the drivers door.
TO
ERASE AND PROGRAM EXISTING REMOTE TRANSMIITERS
1. Open the drivers door and remove the ignition
key.
2. The programming steps must be performed within 40 seconds.
3. Insert the key into the ignition 2
times.
4. Close then open the drivers door 2 times.
5. Insert the key into the ignition 1
time.
6. Close then open the drivers door 2 times.
7. Insert the key into the ignition and leave it in.
8. Close the drivers door.
9. Turn the ignition key from LOCK
to ON, and then back to LOCK position 2 times.
10. REMOVE the key.
11. The tail/rear lights will flash
once, the sounder will sound once and the doors will LOCK and UNLOCK.
12. PRESS the LOCK and UNLOCK button once together on the
remote transmitter to be programmed.
13. PRESS the LOCK button on
the remote transmitter.
14. The tail/rear lights will
flash once, the sounder will sound once and the doors will LOCK and UNLOCK.
15. Repeat steps 12 to 14 for
any additional remote transmitters.
16. OPEN the drivers door.
17. LOCK and UNLOCK the
doors using the drivers door LOCK button 5 times.
18. Insert key into ignition and
turn to the ON position 2 times, then remove the key.
19. LOCKS should cycle from LOCK
to UNLOCK to confirm programming.
20. Press the LOCK and UNLOCK button together on the remote transmitter for 1 second.
21. The LOCKS should cycle LOCK to UNLOCK to confirm programming.